A typical reason of electric powered faults is a inadequately wired plug
A frequent cause of electrical issues is a badly wired plug. Wiring a plug is not difficult nonetheless it is essential to get it correct.
To begin with strip off around 4cm of the external cable sleeve. Slit the sleeve of the cable lengthways using a sharp blade, being cautious not to slice within the coloured wires. Peel the external sleeve apart and reduce it off.
Isolate the wiring and cut to length by using wire blades. Use the plug as a gauge to trim the wire connections to the ideal size. Allowing the wires the same length typically results in the live and neutral wires becoming crushed when the plug cover is changed.
Take away around 5mm of insulation from the ending of every wire using wire strippers/cutters, be careful not to cut into the individual strands of wire. At this point firmly twist the ends of the wires.
Join each wire to the appropriate terminal. Slacken the screw shove the naked wire into the opening and tighten up the screw. Make sure the terminals are small and that there is absolutely no naked wires or free strands of wire showing. It is often easier to press the pins upward slightly when joining the wires.
Brown - Live
Blue - Neutral
Yellow and green - Earth
More aged devices may have different colours:
Crimson - Live
Black - Neutral
Green - Earth
Make tighter the cord clamp over the cable connection sleeving. Make sure the cable clamp is clentching the outside sleeve of the wire not the coloured wires.
Examine that a proper rated fuse is installed. There are 3 regular fuse ratings- 3A, 5A & 13A.
For devices up to 700W a 3A fuse is used.
For those in between 700W and 1200W a 5A fuse is used.
For appliances above 1200W a 13A fuse is used.
Modern electro-mechanical home equipment will have a sticker label or plate showing the maximum power usage in WATTS (W).
Try to make sure there are absolutely no loosened strands of wire in the plug and the wires are laying in the proper routes in the plug and can not come to be crushed while the protect is changed. Double check that the wires are correct and replace the plug's protect and tighten up the screw
Some appliances will simply have a pair of wires - Live & Neutral. Most of these are 'Dual Covered' and do not depend upon the Earth wire for coverage. The plug is wired as above but there is no Earth wire to join, even so try to make certain that the screw on the Earth terminal is not free.
To begin with strip off around 4cm of the external cable sleeve. Slit the sleeve of the cable lengthways using a sharp blade, being cautious not to slice within the coloured wires. Peel the external sleeve apart and reduce it off.
Isolate the wiring and cut to length by using wire blades. Use the plug as a gauge to trim the wire connections to the ideal size. Allowing the wires the same length typically results in the live and neutral wires becoming crushed when the plug cover is changed.
Take away around 5mm of insulation from the ending of every wire using wire strippers/cutters, be careful not to cut into the individual strands of wire. At this point firmly twist the ends of the wires.
Join each wire to the appropriate terminal. Slacken the screw shove the naked wire into the opening and tighten up the screw. Make sure the terminals are small and that there is absolutely no naked wires or free strands of wire showing. It is often easier to press the pins upward slightly when joining the wires.
Brown - Live
Blue - Neutral
Yellow and green - Earth
More aged devices may have different colours:
Crimson - Live
Black - Neutral
Green - Earth
Make tighter the cord clamp over the cable connection sleeving. Make sure the cable clamp is clentching the outside sleeve of the wire not the coloured wires.
Examine that a proper rated fuse is installed. There are 3 regular fuse ratings- 3A, 5A & 13A.
For devices up to 700W a 3A fuse is used.
For those in between 700W and 1200W a 5A fuse is used.
For appliances above 1200W a 13A fuse is used.
Modern electro-mechanical home equipment will have a sticker label or plate showing the maximum power usage in WATTS (W).
Try to make sure there are absolutely no loosened strands of wire in the plug and the wires are laying in the proper routes in the plug and can not come to be crushed while the protect is changed. Double check that the wires are correct and replace the plug's protect and tighten up the screw
Some appliances will simply have a pair of wires - Live & Neutral. Most of these are 'Dual Covered' and do not depend upon the Earth wire for coverage. The plug is wired as above but there is no Earth wire to join, even so try to make certain that the screw on the Earth terminal is not free.
Source...