The 6 Step Basic Blueprint for Novices to Make Homemade Solar Panel!
Are you ready to make homemade solar panel?
One thing you need to remember is that building homemade solar panel is quite simple and doesn't require extensive technical know-how.
Okay, here's a basic 6 step blueprint to make homemade solar panel which I learned from viewing step-by-step video tutorials downloaded to my computer hard drive.
Head over to your nearest hardware store and acquire the following items:
1) Blocking diodes
2) Copper wires
3) One sheet of Plexiglass
4) Plywood Panel
5) Silicone Sealant
6) Solar cells
7) Solder and soldering pen
8) Stainless steel screws
9) UV coating paint
10) Wood to form panel border
My total cost: $206
1) Cut up the plywood according to the amount of solar cells you have in possession. To generate say 100 watts of power, you'll need about 80 solar cells. Build and combine multiple panels if you require more power.
2) Paint the plywood panel with UV coating paint. Once done, you can start joining the solar cells together. Place all the cells on the ground and using the soldering pen, drop very little amount of solder onto the small tabs found at the back of each solar cell.
3) The solder applied on the tabs allows you to link all the cells together with the copper wire. The top of the soldered tab is where you put the wire and to make it stick, just press it down until the solder cools off..
4) Now what do you see across the back of the solar cells? Two lines of copper wire! The setup goes like this: The negative end of the wire goes to the negative slot and positive enters the positive slot.
5) Time to link up the cells! Arrange the wiring in such way that the negative wires are unable to come into touch with the positive wires.
6) Drill 2 holes to get the wire out of the back of the plywood panel, add the wood to form a border around the cells, screw from the back and finally with the silicone sealant in hand put the Plexiglass sheet on top of the panel.
Keep in mind that, if you watch step-by-step video tutorials like I have, then it will be a whole lot easier to make homemade solar panel!
Have you got the time to view instructional videos on how to make homemade solar panel [http://www.articlesbase.com/diy-articles/the-6-step-basic-blueprint-for-novices-to-make-homemade-solar-panel-1828878.html]?
You can obtain download details to 6 step-by-step video series plus a few printable manuals by following this link -- > http://www.howtobuildyourownsolarpanel.com/
One thing you need to remember is that building homemade solar panel is quite simple and doesn't require extensive technical know-how.
Okay, here's a basic 6 step blueprint to make homemade solar panel which I learned from viewing step-by-step video tutorials downloaded to my computer hard drive.
Head over to your nearest hardware store and acquire the following items:
1) Blocking diodes
2) Copper wires
3) One sheet of Plexiglass
4) Plywood Panel
5) Silicone Sealant
6) Solar cells
7) Solder and soldering pen
8) Stainless steel screws
9) UV coating paint
10) Wood to form panel border
My total cost: $206
1) Cut up the plywood according to the amount of solar cells you have in possession. To generate say 100 watts of power, you'll need about 80 solar cells. Build and combine multiple panels if you require more power.
2) Paint the plywood panel with UV coating paint. Once done, you can start joining the solar cells together. Place all the cells on the ground and using the soldering pen, drop very little amount of solder onto the small tabs found at the back of each solar cell.
3) The solder applied on the tabs allows you to link all the cells together with the copper wire. The top of the soldered tab is where you put the wire and to make it stick, just press it down until the solder cools off..
4) Now what do you see across the back of the solar cells? Two lines of copper wire! The setup goes like this: The negative end of the wire goes to the negative slot and positive enters the positive slot.
5) Time to link up the cells! Arrange the wiring in such way that the negative wires are unable to come into touch with the positive wires.
6) Drill 2 holes to get the wire out of the back of the plywood panel, add the wood to form a border around the cells, screw from the back and finally with the silicone sealant in hand put the Plexiglass sheet on top of the panel.
Keep in mind that, if you watch step-by-step video tutorials like I have, then it will be a whole lot easier to make homemade solar panel!
Have you got the time to view instructional videos on how to make homemade solar panel [http://www.articlesbase.com/diy-articles/the-6-step-basic-blueprint-for-novices-to-make-homemade-solar-panel-1828878.html]?
You can obtain download details to 6 step-by-step video series plus a few printable manuals by following this link -- > http://www.howtobuildyourownsolarpanel.com/
Source...