Tips on How to Handle When Something Goes Wrong With Your Hot Tubs
Using an elegant hot tub or Leslie pool for your family will be a great pleasure, especially when many reputed brands, interesting designs and useful options are available in the market. Even though you are familiar with the designing and functional excellence of hot tubs, but you should be little more careful about its use. The use of complicated water-based and electrical and systems in these tubs may create problems after repetitive or careless use.
Below are given a few common issues that you may face from time to time.
€ Unbalanced water chemistry - The water in your hot tub should have balanced PH otherwise it might make your family members sick. You need to focus on adding the right amount of chemicals to the water. If you go on adding fewer chemicals, it might cause corrosion in the pump system and lead to tub seal leaks. If more chemicals are added, people taking bath in your tub may start to feel irritation in their eyes or skin.
€ Pump seal leakage - If you get a small pool of water under or close to your hot tub pump, there might be a leak in seal shaft. The leak may be due to chemical or water corrosion but you should treat it at the earliest. Otherwise leaking water may penetrate into the system and cause mechanical failure.
€ Clogged filter or drain - When the heat system in hot tubs doesn't work properly, clogged drain or filter might occur. You will have to clean and replace the filter regularly in order to ensure that each drop of tub water moves through it smoothly. Consider to replace it if it is above 2 years old.
€ Burned out pump circuit board in Leslie pools or hot tubs - When the PH of your tub water is very low, the heating system begins to erode fast. The imbalance in PH factor makes the GFCI breaker to trip and prevent users from electric shock. In fact, the loosely connected terminal screws may cause the pump circuit boards to burn out. It not only produces high heat but also transfers them to the board causing instant failure.
€ Defective thermostat - Hot tub water temperature gets controlled by the thermostat. If it is turned down mistakenly, then water in your tub won't get heated. Many newly introduced hot tubs have a solid state controller and thermostat fixed on the circuit board. If any of them fails then you will have to go for a replacement. The thermostat may start to give problem if there is defective insulation in your spa or tub. As a result, heat is lost to the environment and your tub water does not remain warm any more.
What can be done to overcome these problems?
With little care and attention you can manage to overcome these problems. So, keep it clean and repair in case you are finding any minor issues that can escalate further.
1. Tub water testing - Use a PH meter to test the chemical nature of tub water before each time you get into it. It will ensure that the water is neither highly acidic nor highly alkaline.
2. Don't think that hot tubs are free from maintenance and can balance chemicals automatically. Try to keep its water clean with new filter cartridges and maintain optimal balance of PH with frequent addition of chemicals.
3. Consider or drain the water inside a tub and refill it if the TDS level goes beyond 1500 ppm on testing.
4. Keep the tub covered and repair every minor to major damage occurring in the tub surface as it might affect heating, insulation and the general lifespan of the thermostat as well.
Below are given a few common issues that you may face from time to time.
€ Unbalanced water chemistry - The water in your hot tub should have balanced PH otherwise it might make your family members sick. You need to focus on adding the right amount of chemicals to the water. If you go on adding fewer chemicals, it might cause corrosion in the pump system and lead to tub seal leaks. If more chemicals are added, people taking bath in your tub may start to feel irritation in their eyes or skin.
€ Pump seal leakage - If you get a small pool of water under or close to your hot tub pump, there might be a leak in seal shaft. The leak may be due to chemical or water corrosion but you should treat it at the earliest. Otherwise leaking water may penetrate into the system and cause mechanical failure.
€ Clogged filter or drain - When the heat system in hot tubs doesn't work properly, clogged drain or filter might occur. You will have to clean and replace the filter regularly in order to ensure that each drop of tub water moves through it smoothly. Consider to replace it if it is above 2 years old.
€ Burned out pump circuit board in Leslie pools or hot tubs - When the PH of your tub water is very low, the heating system begins to erode fast. The imbalance in PH factor makes the GFCI breaker to trip and prevent users from electric shock. In fact, the loosely connected terminal screws may cause the pump circuit boards to burn out. It not only produces high heat but also transfers them to the board causing instant failure.
€ Defective thermostat - Hot tub water temperature gets controlled by the thermostat. If it is turned down mistakenly, then water in your tub won't get heated. Many newly introduced hot tubs have a solid state controller and thermostat fixed on the circuit board. If any of them fails then you will have to go for a replacement. The thermostat may start to give problem if there is defective insulation in your spa or tub. As a result, heat is lost to the environment and your tub water does not remain warm any more.
What can be done to overcome these problems?
With little care and attention you can manage to overcome these problems. So, keep it clean and repair in case you are finding any minor issues that can escalate further.
1. Tub water testing - Use a PH meter to test the chemical nature of tub water before each time you get into it. It will ensure that the water is neither highly acidic nor highly alkaline.
2. Don't think that hot tubs are free from maintenance and can balance chemicals automatically. Try to keep its water clean with new filter cartridges and maintain optimal balance of PH with frequent addition of chemicals.
3. Consider or drain the water inside a tub and refill it if the TDS level goes beyond 1500 ppm on testing.
4. Keep the tub covered and repair every minor to major damage occurring in the tub surface as it might affect heating, insulation and the general lifespan of the thermostat as well.
Source...