A Really Simple and Accurate Way to Measure Your Penis
Most men are interested in measuring their penises at some point in their lives.
Especially those men who are interested in enlargement programs and want to monitor their progress.
Even many women are fascinated by these measurements and take part in measuring their partner's penises.
The problem is that a penis is hard to measure accurately! Here is a method that takes a lot of the inaccuracy out of measuring your penis.
It's the best method that I know of.
Get a tall, clear drinking glass.
It has to be longer than the length of your penis when it is erect (especially if you are interested in enlargement, make sure you have at least 5 inches of extra length in the glass).
You can use a large test tube, too, and can pick one of these up at a chemical/laboratory supply place.
The tube or glass must NOT have any ridges.
It must be smooth.
Get a grease pencil and your glass; and get your erection ready.
Get as solid an erection as you can.
Slip the open end of the tube or glass over your penis and press it snuggly against your body.
Center it so that the penis rests at the top of the glass (as you are looking down on it), but not pressing too hard against it.
You will see your penis, now, inside of the glass.
Now, using the grease pencil, make a horizontal line at the very tip of the penis.
At the middle of the shaft, make two longitudinal lines on either side of the penis.
Remove the glass and using a soft tape measure, measure from the lip of the glass to the horizontal line.
This is your length.
Measure the distance between the two longitudinal lines and this will give you a basis for your width (or diameter).
Write these numbers down if you are interested in penis enlargement.
To calculate your girth, use the equation: C = D * Pi Where: C is Circumference (girth).
D is the Diameter (you just measured this).
Pi = 3.
14159 So, if your width (diameter) of your penis is 1", your girth would be 3.
14".
If you are in a penis enlargement plan, mark the date on the three lines on your glass and put the glass some place safe so it will not be disturbed.
When you go to re-measure your penis, just use the same glass and you can compare the old lines with the new lines.
You can even outline the shaft or head if you desire but try and be accurate.
It's the simplest and most accurate method available.
It beats trying to scan or photocopy your penis! Good luck.
To learn more about Natural Penis Enlargement, read IRON MAN PENIS - THE RUSSIAN SYSTEM and start now to Enlarge Your Life.
Enjoy your day, Georg von Neumann
Especially those men who are interested in enlargement programs and want to monitor their progress.
Even many women are fascinated by these measurements and take part in measuring their partner's penises.
The problem is that a penis is hard to measure accurately! Here is a method that takes a lot of the inaccuracy out of measuring your penis.
It's the best method that I know of.
Get a tall, clear drinking glass.
It has to be longer than the length of your penis when it is erect (especially if you are interested in enlargement, make sure you have at least 5 inches of extra length in the glass).
You can use a large test tube, too, and can pick one of these up at a chemical/laboratory supply place.
The tube or glass must NOT have any ridges.
It must be smooth.
Get a grease pencil and your glass; and get your erection ready.
Get as solid an erection as you can.
Slip the open end of the tube or glass over your penis and press it snuggly against your body.
Center it so that the penis rests at the top of the glass (as you are looking down on it), but not pressing too hard against it.
You will see your penis, now, inside of the glass.
Now, using the grease pencil, make a horizontal line at the very tip of the penis.
At the middle of the shaft, make two longitudinal lines on either side of the penis.
Remove the glass and using a soft tape measure, measure from the lip of the glass to the horizontal line.
This is your length.
Measure the distance between the two longitudinal lines and this will give you a basis for your width (or diameter).
Write these numbers down if you are interested in penis enlargement.
To calculate your girth, use the equation: C = D * Pi Where: C is Circumference (girth).
D is the Diameter (you just measured this).
Pi = 3.
14159 So, if your width (diameter) of your penis is 1", your girth would be 3.
14".
If you are in a penis enlargement plan, mark the date on the three lines on your glass and put the glass some place safe so it will not be disturbed.
When you go to re-measure your penis, just use the same glass and you can compare the old lines with the new lines.
You can even outline the shaft or head if you desire but try and be accurate.
It's the simplest and most accurate method available.
It beats trying to scan or photocopy your penis! Good luck.
To learn more about Natural Penis Enlargement, read IRON MAN PENIS - THE RUSSIAN SYSTEM and start now to Enlarge Your Life.
Enjoy your day, Georg von Neumann
Source...