Setup And Configure A Router With Computer Support
Your home or small enterprise networking performance can be greatly influenced by the router. A router can provide great help when the matters like sharing Internet access or setting security protocols come to the forefront. Another amazing point about a router is that it puts a hardware firewall between the home network and the outside Internet and thus protects the home computer from serious virus attacks.
So if you are thinking how could you set up and configure your new router you can follow some computer support steps so that setting and configuring it up would become a fun to you. If you have bought a wireless router you can see two antennas at the rear side of the router. Some lights you can found on the router which will signal the power or activity when you light these up. You will find connections to LAN and WAN ports at the back of the router. These ports will allow you to connect these to computer with a Cat5 Ethernet cable.
Computer support experts suggest that for login to the router for the initial phases you will need to use patch up cable. You need to launch a web browser and in the address bar you will need to type 192.168.1.1. After this you need to press Enter. It will take you to the login screen of the router. But if you did not reach to the router login screen then you may be need to try another address that is 192.168.0.1.
When you enter on that page you will be shipped into a default login. Computer support experts suggest that you must change that login immediately. Consult the documentation that comes up with the router. If you do not have the needed reference you can use admin as login and password.
Computer support experts now suggest you to decide on DHCP. You can enable DHCP if you want your router to handle all the IP address on different computers on your LAN. The fact is that when your PC connects to the router it looks for a DHCP server. Your router then will reply back with assigning a unique IP address to that particular computer. Each computer on the network will do the same thing and the router will assign them with different IP addresses since it knows the IPs. However, you can run a static IP too.
Computer support experts now suggest you to set the SSID. These SSID must set to be matched with the workgroup name that all the computers have on the LAN. If this is overlooked, you wont be able to connect the machines or the Internet. First you need to set the SSID for the router and then you need to go around to each computer to change its workgroup name. For doing this you will need to go to the section My Computer. You should go now to Properties. Then you need to go on computer name. Now you will need to click on the button Network ID and then to Change button. You will need to give the same name that you used for SSID under the section workgroup. After you are done you will need to reboot your computer.
So if you are thinking how could you set up and configure your new router you can follow some computer support steps so that setting and configuring it up would become a fun to you. If you have bought a wireless router you can see two antennas at the rear side of the router. Some lights you can found on the router which will signal the power or activity when you light these up. You will find connections to LAN and WAN ports at the back of the router. These ports will allow you to connect these to computer with a Cat5 Ethernet cable.
Computer support experts suggest that for login to the router for the initial phases you will need to use patch up cable. You need to launch a web browser and in the address bar you will need to type 192.168.1.1. After this you need to press Enter. It will take you to the login screen of the router. But if you did not reach to the router login screen then you may be need to try another address that is 192.168.0.1.
When you enter on that page you will be shipped into a default login. Computer support experts suggest that you must change that login immediately. Consult the documentation that comes up with the router. If you do not have the needed reference you can use admin as login and password.
Computer support experts now suggest you to decide on DHCP. You can enable DHCP if you want your router to handle all the IP address on different computers on your LAN. The fact is that when your PC connects to the router it looks for a DHCP server. Your router then will reply back with assigning a unique IP address to that particular computer. Each computer on the network will do the same thing and the router will assign them with different IP addresses since it knows the IPs. However, you can run a static IP too.
Computer support experts now suggest you to set the SSID. These SSID must set to be matched with the workgroup name that all the computers have on the LAN. If this is overlooked, you wont be able to connect the machines or the Internet. First you need to set the SSID for the router and then you need to go around to each computer to change its workgroup name. For doing this you will need to go to the section My Computer. You should go now to Properties. Then you need to go on computer name. Now you will need to click on the button Network ID and then to Change button. You will need to give the same name that you used for SSID under the section workgroup. After you are done you will need to reboot your computer.
Source...